Control Box Controller

MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035 —

MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035
MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035
MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035

MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035
Unit Basic Digital Control And Fuse Box. Within the DIY rewire-your-whole-bike food chain, the m-Unit Basic is an evolutionary step forward from the very popular m-Unit V2 and it only lacks the Bluetooth functionality found on the m-Unit Blue. All told, there’s 12 input channels on one side then 10 output channels on the other. Designing electrical circuits and wiring up your bike is still a difficult task, however the m-Unit Basic makes it easy as it can be since it has been specifically engineered for the task. With the m-Unit Basic, circuits are digitally monitored -this means if you have an overload somewhere, the circuit will be tripped and an LED next to your output will flash. Correct the issue, re-cycle the m-Unit and get back on the road. Complete digital control using buttons possible with 4 or 5-button operation. Complete replacement for the fuse box. 10 independent circuits are digitally monitored and switched off if there are faults, after the fault is rectified, the safety function is automatically reset. Integrated alarm system that can be installed in any position. Integrated, digital flasher relay that is load-independent; automatic switch-off optional and can be set; m. Wave mode can be selected. Integrated hazard warning light. Turn signal can optionally be set as a positioning light. Integrated parking light and headlight flashing. Lo-beam and Hi-beam (up to 200 W switched capacity) can be controlled using only one button. Integrated, digital brake light modulator; flashing mode can be programmed. Acceleration-controlled emergency brake light (automatic warning signal). Integrated starter relay for the starter system with solenoid (up to 30A switched capacity). Intelligent and configurable management/switch-off of power consuming devices so that the maximum starting energy from the battery can be used when starting the motorbike. Integrated digital horn relay. Two configurable additional outputs AUX1 and AUX2. Diagnostics function for assigning inputs, outputs, the circuit switching status, short circuit diagnostics etc. Calibration and current measurement enables faults to be detected on all lamps. 101mm L x 61mm W x 28mm H (3.97″ L x 2.40″ W x 1.10 H). Fasteners: 2 x M5 stainless steel bolts (installation and ground connection), 1 x M5 screwing contact for battery Plus. Operating voltage: 6 V – 20 V. 1 x input (+12 V switched) for ignition lock or m. 11 x control input (minus/switched to ground) for. 10 x Outputs (+12V) for. 50cm connecting cable for battery positive terminal with 10mm² cross section. 1 x M5 stainless steel bolt. 2 x M5 stainless steel bolts with nut. 1 x speed sensor with 2 magnets. Detailed installation and operating instructions. The item “MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035″ is in sale since Monday, August 13, 2018. This item is in the category “eBay Motors\Parts & Accessories\Motorcycle Parts\Instruments & Gauges\Other Instruments & Gauges”. The seller is “aandjcycles” and is located in Tuxedo Park, New York. This item can be shipped worldwide.
  • Manufacturer Part Number: MG4002035
  • Brand: Motogadget
  • Warranty: Yes

MOTOGADGET M-UNIT BASIC DIGITAL CONTROL UNIT NEW Fuse Box MG4002035

Categorised as: motogadget

Comments are disabled on this post


Comments are closed.